![]() ![]() As it's a basic ist creation guide, so only important sections has been discussed.This will cause less trouble and speedup the installation process. Once you install, you can add the other options later on. It's good to have a minimal configuration and options set before you install.However, for few systems, such as Xeon, High End CPUs, Workstations, Server, X99, X299, you might need to tweak your ist.įor Laptop users, a separate thread is available. This guide covers a creation of basic ist which will allow to boot most of the systems. The best way to edit a ist is to use some specific tools like Clover Configurator, Xcode, Plist Editor Pro etc. But we don't recommend you to use a text editor as it has a chance of ist file corruption. The configuration file is written in XML and can be edited using a text editor. It can boot into some installation but when talking about the majority, it will fail to boot on most of the newer machines and high end builds.Īlso, it's a good idea to create a ist for each specific system which will exclude the errors and trouble while installation and you can easily boot into macOS installation. The ist which is installed by Clover Boot loader, is the default ist and is not optimised for all the systems. If the ist is already present, it will be renamed as backup ist or remain untouched. Without a ist, no machine can boot into macOS.Ī basic ist file is automatically created while installing Clover Boot loader at /EFI/Clover/. The ist is a system configuration file for the Hackintosh and allows to boot macOS. Install the battery strap and connect the flight controller to the Raspberry Pi using a USB cable.By following this guide, you'll be able to create a basic ist for booting macOS on Desktop. Install the mounting deck and fix it with M3x8 bolts.Įstablish protection and fix on beams by means of self-locking nuts and M3x10 screws. From below, between the plates of the legs, install a damper silicone ring.īend the legs back and install a hoop with LED strip in a special groove on them so that the connection cables exit from the tail side of the copter.īehind fasten the legs with self-locking nuts and M3x10 screws.Ĭonnect the LED strip power (red, black cables) to the short JST connector on the PDB.Ĭonnect the signal output of the LED strip (white cable) to Raspberry Ri, to pin GPIO21.Īssemble the lower level of guard with 40mm racks and M3x10 screws.Īssemble the top level of protection with the M3x10 screws. Install the legs on the stiffening plate using self-locking nuts and M3x8 screws using only the extreme mounting holes. Stick the LED strip on the hoop, for better fastening, pull it with 3-4 clamps. Install the assembled pickup deck and fix with the M3x8 screws.Ĭonnect to the Raspberry Pi rangefinder and power cable.Ĭonnect the camera cable to Raspberry Pi.Īssemble the hoop for the LED strip by combining the lock on the ends. Install the camera module on the capture deck and fix with the M3x8 screws. ![]() Install the camera on the small mounting deck and fix it with 2 M2x5 self-tapping screws in the upper left and lower right corners. Install 4 20 mm racks and fix them with the M3x8 screws. ![]() On the capture deck, install the rangefinder using self-locking nuts and M3x8 screws, and glue the radio using double-sided tape. Install the Raspberry Pi circuit board and fix with M2.5x4 bolts. Install the assembled mounting deck on the main deck and fix with the M3x8 screws. On a mounting deck, install M2.5圆 mm racks and M3x30 mm racks, fasten them with the M2.5x4 and M3x10 bolts, respectively. Install 40mm aluminum racks on the M3x10 screws. Glue 3-4 layers of double-sided tape, glue it in the center of the small deck and install Pixracer on top.Ĭonnect the speed controllers to the flight controller in accordance with the diagram.Ĭonnect the power cable to the power distribution board(PDB) and the corresponding connector on the flight controller. Place the small deck on the racks and secure it with nylon nuts. Install the damper struts, fix COEX Pix on them with nylon nuts. COEX Pixīefore installing the damper struts, screw 2 layers of nylon nuts, for a stronger fix or bite off the excess thread using side cutters. The power distribution board must be installed so that the power connection cable points toward the tail of the aircraft.Ĭonnect the power outputs of the speed controllers to the power distribution board.Ĭlover 4 drone kit allows you to install various flight controllers, for example COEX Pix and Pixracer.ĭuring installation the flight controller, pay attention to the arrow located on the board, it should be directed to the copter bow. Install the power distribution board (PDB) on the pre-mounted racks and secure it with 6mm racks. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |